AUTONET TV

Don't Blow a Gasket! (Valve Cover Gasket Replacement)

When you head out to your vehicle after it's been parked and notice oil leaking underneath it, that's something to have looked at right away.  Oil leaks mean your oil level is probably low and running a vehicle in that condition can lead to expensive repairs.

While there are many reasons oil leaks develop, one possibility is a bad valve cover gasket.  Vehicle engines have a cover bolted over the spot where the engine valves are, and that cover keeps the oil inside the engine. In between the cover and the engine is a gasket that keeps that seal tight.  But after many years of high engine temperatures and vibrations, that gasket or the bolts that hold on the valve cover can fail or loosen, and oil can leak.

You may see dirty oil on the valve cover in the engine compartment, near the spark plugs, or around the bolts that hold the valve cover on.  All those are signs of leakage and time to bring your vehicle in for our technicians to check out.

In some vehicles, taking off the valve cover and replacing the gasket is a relatively easy job. In some models, though, other engine parts are located near that part of the engine and must be removed to get at the gasket, so repair costs can vary widely.

The technician will measure to make sure the valve cover isn't warped so it can be reused. If it is warped, they'll recommend replacing it with the gasket.  

While the technician has that area of your engine accessible, they will also check to see if other components need replacing at the same time, which could save you money.  And because valve cover gaskets usually fail in older vehicles, the technician will check for other oil leaks then, too. 

One of the best ways to be sure your valve cover is doing its job is to have your vehicle regularly maintained.  The technician will periodically look over your engine compartment and make sure you know when things are showing signs of age and wear BEFORE they fail and leave you stranded.

All Things Automotive & Diesel Service
1997 Walton Ave #C
Idaho Falls, ID 83401
208-523-3903

Oh, Stop! (Disc Brake Service)

Every time you drive your vehicle, you wear down your brakes just a little bit.  And after a while, that adds up.  Gradually, your stopping power isn't like it used to be.  Since brakes are one of your vehicle's most important safety features, it just makes sense to keep them performing well.

Most vehicles have disc brakes.  One key component, as the name suggests, is the disc.  Most vehicles have discs on their front and rear wheels.  The discs (also called rotors) are made of metal, and each rotates with the wheel hub.  Your brakes also have pads that make contact with the rotors when you press down on the brake pedal, and the friction stops your vehicle.

After many, many stops, that friction wears down both the pads and the discs and reduces their ability to stop the way you need them to.  The discs may also become uneven from all the heat they generate, and your brakes won't stop as well as they used to when they were newer. 

Some signs that your rotors need attention include vibration at the wheels when you stop, discolored rotors (the metal looks blue), excessively hot rotors, or grooves in the metal.  If you see any of these signs, it's time to bring in your vehicle for us to inspect your brakes. 

A technician will measure the thickness and trueness of the rotors and check the surfaces for wear.  If they need to be replaced, they'll be done in pairs, so if a front rotor is bad, the other front rotor will also be replaced. Usually, your brake pads will be replaced at the same time.  You can ask your service advisor if higher-performance brakes would benefit you.

When your vehicle is at the shop, the technician will check other components of your brake system to make sure they are operating safely. Brakes are vital to the safe operation of your vehicle.  Keep them well maintained so they can be there when you need them.

All Things Automotive & Diesel Service
1997 Walton Ave #C
Idaho Falls, ID 83401
208-523-3903

Alleviate the Creaks and Squeaks (Chassis Lubrication)

If your vehicle creaks and squeaks when you drive down the road, it may mean that some of the metal parts are rubbing against each other and need to be lubricated.  Those could be parts of the suspension, steering system and the drivetrain. 

Years ago, most vehicles had to have their chassis (what you think of as the frame) regularly lubricated.  Newer vehicles are made with what some call "lifetime lubrication," but there are still parts of the chassis that need to be maintained with lubricants.  Your service advisor can help you know when that needs to be done.

In your owner's manual, the vehicle's manufacturer lists components that need regular maintenance. Things like u-joints, steering joints, sway bars, bushings and joints in the suspension. Some of them may have that "lifetime lubrication," while others may not. When you bring your vehicle in for service, a technician will look for any parts that have grease fittings.  They will inspect these components, clean the fittings so dirt and other contaminants won't be forced into the part and then lubricate them with a lubricant that meets the manufacturer's specifications. 

Sometimes a chassis lubrication is done at the same time as an oil change.  That's also an ideal time for the technician to check other parts of your vehicle that may need attention.  That could include greasing other parts such as the fuel door, trunk and door hinges, suspension springs and door latches.

Times have changed since the days when a "lube" job was synonymous with an oil change. Depend on your owner's manual and advice from your service advisor to know when "grease" is the word—and appropriate for your vehicle.

All Things Automotive & Diesel Service
1997 Walton Ave #C
Idaho Falls, ID 83401
208-523-3903

Bad Vibrations (Brake Rotor Replacement)

If you’ve ever stepped on your brake pedal and felt your vehicle vibrate, that’s a signal that you shouldn’t ignore.  A pulsating brake pedal is a sign that something is wrong.  Braking action should be smooth, sure, and quiet, not shaky and noisy.

Most newer vehicles have disc brakes, called that because they have a round, flat disc connected to each wheel.  Those discs are the rotors. Other parts called brake pads are squeezed against those discs when you press on the brake pedal.

Remember that vibration we mentioned? That can be caused by the rotor not having a straight, true surface. Rotors can heat up from friction and warp.  They can become thinner from constant wear.  Rotors can rust from the elements they’re exposed to, such as rain, snow ice, and salt.  They can get grooves in them from so many contacts with the pads. 

The signs of worn rotors are vibrations, grooves on the rotor (which you can see sometimes through open spots in the wheel) noise such as squealing or scraping when you brake, and increased stopping distance.   

While it used to be common for rotors to be machined (shaved down to restore their flat surface), newer vehicles have thinner rotors, so your service adviser may suggest you replace rotors when they start showing signs of significant wear.

Brakes are important safety equipment for every vehicle.  They enhance your control while driving, so it’s important that they be regularly inspected and maintained.  A good time is when you have your tires rotated. A technician can then look at all components of your brakes and recommend any service you may need to keep your brakes in top shape.

All Things Automotive & Diesel Service
1997 Walton Ave #C
Idaho Falls, ID 83401
208-523-3903